MIDI TemplatesRe: (Case 131665) FW: Replacement potentiometer model for the EQ knobs on my Novation TwitchGareth Butt
Re: (Case 131665) FW: Replacement potentiometer model for the EQ knobs on my Novation Twitch
Hi Gareth,
Thanks for the reply,
We will still repair your unit under warranty. Please speak to your dealer, and they will be able to arrange a warranty repair for you,
Best Regards, --
Will Kent // Focusrite Technical Support
http://www.focusrite.com/answerbase/en/
Focusrite Audio Engineering Limited
Windsor House, Turnpike Road, High Wycombe HP12 3FX, United Kingdom
-----Original Message-----
From: "Jo Andrews"
Reply-To: "Jo Andrews"
Date: Fri, 13 Apr 2012 08:55:52 +0100
To: "Support Team"
Subject: FW: Replacement potentiometer model for the EQ knobs on my Novation Twitch
>Jo Andrews
>
>Sales Admin
>Focusrite Audio Engineering Ltd
>
>Windsor House | Turnpike Road | High Wycombe | Buckinghamshire | HP12 3FX | UK
>
>From: Gareth Butt [mailto:garethbutt@hotmail.com]
>Sent: 12 April 2012 19:53
>Cc: Sales
>Subject: Replacement potentiometer model for the EQ knobs on my Novation Twitch
>
>Dear Novation
>
>I am writing to ask if you could provide me with details of the correct potentiometer model for the EQ knobs on my Novation Twitch and how I can purchase them.
>
>The Twitch knobs were a nightmare to remove (at least on my model). No amount of teasing with my fingers or using an old cloth or rubber gloves to add traction helped. Eventually I had to resort to padding out the jaws of a pair of pliers to gently pull off the old knobs. This worked for all but two of them: when I slowly pulled them off, the metal D-shafts inside the knobs themselves also came out from inside the potentiometers. These were an absolute devil to put back in - the 'end stops' on one knob have broken so it now acts like an endless encoder.
>
>I imagine because I have attempted to replace the knobs I am no longer covered by my warranty on the Twitch. If this is so, I would be very grateful if you could provide me with details of how I can purchase replacement potentiometers for the Twitch.
>
>Purchased from decks.co.uk 28/03/2012
>
>decks.co.uk Order D883B9EB
>
>Back of Twitch/side of box details:
>
>NOVDJ0002
>IT7132506690
>
>Kind regards
>
>Gareth Butt
Don't look for the PG-300, your Remote can do it!
This template makes available all MKS-50 Tone parameters and the most useful Patch parameters, and surpases the control capabilities of the hardware programmer PG-300.
ZIP file includes the template sysex file, a PDF with comments on how controls are organized (both in Spanish and English), and a JPG with a ‘paper’ clone of the template.
If you like it, let me know! Drop me a line pablo@cicloquintas.es
MIDI TemplatesROLAND SONICCELL PARTS CONTROLPablo Fernández-Cid
Template for SonicCell performance mode.
Right faders: volume for parts 1-8. Right buttons: on/off for the 16 parts.
Left side: continous control of cutoff & resonance, and step control for attack and release. Also control for master transpose and volumen. Drum pads trigger notes.
Very uselful for live setup, can fool any keyboard into a master (using parts on/off to change sounds on the fly). Programmed with sysex messages (they should use 'Roland' sysex with checksum, but here uses ordinary sysex -that somehow works fine for the SonicCell-). Also useful working with midi files (turn tracks on/off, etc.).
This is a simple 2 deck mapping I got of the internet to use your launchpad for the deck controls on Traktor. There is led feedback and it's an easy simple set up. Enjoy
this is the Maschine (Native Instruments Groove Maschine/Midi Controller) Part with Orb on/of, Aux2 Pan , with the Pads(Page H) you can Control Live Parts and Start/End Latch Mode on each Part in Live Mode
Best load it in Controller Editor, so you can see
This is for the V-synth and XT. These are all basic CC controls which are useful for performance. The Time Trip pad works perfect. D-beam use the sliders. Controls 1 and 2 use the lower knobs. HELP: If someone knows how to implement roland Sysex with Remote SL please modify this template. The V-synth midi implementation guide is here: http://lib.roland.co.jp/support/en/manuals/res/1811378/V-Synth_v2_MIDI_Imple_e1.pdf
Hope you like this template!!
For basic controls of the Novation UltraNova Synth on A SL MKII Midi controller (Was Made on A 61SL MKII)
Note:
The Touch Triggers Only seem to work while the Ultranova is in Touch Mode If you go Out of Touch Mode The Touch Triggers will all be turned OFF and will be OFF when re-entering Touch Mode
(Yes, Touch Triggers can be turned ON and OFF with this template)
Enjoy
set kore Midi Hardware Kontroller (Options-Hardware-MidiController)Knobs 8-15, Buttons 32-39, X-Y morph 58-59 (just type with your Keyboard or mouse), download novation beta SL MK2-editor,start it, klick on File-open and choose the SkaRulez-kore file, press edit on your Zero MK2, touch TmpGroup and choose a empty template, then click "upload" in the editor window, if you like it save with write on the MK2
